Full Dip Clear Matte Aerosol Spray

Full dip clear is mostly used for clear bra,spoiler or paint protection on your car. Use it over standard OEM paint and it will give it a matte finish.
I have used it on rear van glass to give a frosted privacy look and still let plenty of light in. Just apply on inside of glass to avoid unwanted removal.
Also used as top coat for any full dip colour to give matte finish, Great water & corrosion protection for marine electrical connections as it is easy to remove.
Just make sure electrical circuits are isolated by professional before use and allow full dip to completely dry.

Aerosol application
2 very light dust coats followed by 4 or 5 wet coats.

4 Litre Sprayable application
Recommended guns;
FD650
MS3000
Compressor setup and 1.7 tip @ 20-28 PSI

Full Dip clear Matte Can change the colour finish of your Car, motorbike, alloy wheels to a matte finish.
Use around the Home or Garden, arts & crafts. You can full dip almost anything.
Our Full Dip aerosols include two nozzles, each designed for a function: standard nozzle flow and high-flow nozzle for larger areas. Simply swap them to get the fan size you want, wide and wider.

Full Dip matte range

Will wrap, protect and change the look of your project with a matte finish.
It can be removed by peeling it, as if it were a conventional vinyl.
Long research and development process from pioneers in the liquid vinyl spray for quality products.

Properties

Full Dip 400ml spray covers up to 1.2 meters sq.
Air dried, flexible, liquid coating for use on almost anything
Liquid Vinyl spray application, once dry becomes a tough elastic and durable film.
It can be easily removed from most surfaces if required,Plastic,glass and metal.
You will need an average of 4-6 coats. Add more layers for greater protection. Sprayable Liquid Wrap in a Can.

You can clean Full dip with most soaps, and it will resist water, mud or pressure water cleaning.
No cracks or self peeling over time, remains flexible and stretchy, and will not become brittle or crack.

Before Application

1. SURFACE PREPARATION
Before you start spraying the liquid vinyl, you need to have the surface completely clean, dry and free of any substance that may be capable of causing non grip (as waxes, cleaners etc). It is advisable to ensure that the surface is clean as possible without dirt (such as sand , dust, road tar, brake dust etc.) Full Dip® will bond to the surface you spray it on, and thus, if the surface is not 100% clean, you will get imperfections and faults.
So it is important you clean properly (even those annoying parts and between spokes on wheels). Cleaned perfectly and you will get uniform even finish that lasts years.

1.2 TOLERANCE TEST
Full Dip® can be applied to any surface such as metals, plastics, glass, wood, etc.. However it may best to do a small pre-test on an insignificant part of your project before committing to the full project to make sure it is 100% compatible to what you are spraying over with no adverse reaction.

2. APPLICATION OF Full Dip®

2.1 SHAKE IT
Shake vigorously before use. At least a minute to mix all the internal elements.

2.2 SPRAY IT

Apply the product approx. 20 cm range. Always parallel to the surface you are spraying. You can apply as many coats as you want, keeping in mind that you will need an average of 4-6 coats. But remember, that more coats you apply, the more durable it will be. The result will be better and more easily peeled if you want to remove in the future. Use less coats, two or three, then expect problems like hard to remove,poor finish and durability. Between coats, you must wait at minimum 10-30 minutes. Full dip will be touch dry in 10-30 minutes, but to be completely dry you need wait 12 hours. We recommend 100% using a proper PPE mask during application. Once dried / cured, your project is ready to use.

Instructions for use on full dip Clear matte, please go to our application Guide.